Memorex MT1192A User Manual download pdf (Page 3)

LOCATION OF CONTROLS

CH (CHANNEL) and buttons

Press and release the CH (CHANNEL) or button. The channel automatically stops

at the next channel set into memory. Press and hold the button down to change channels

more quickly.

For proper operation, before selecting channels, they should be set into the TV's

memory. See "To Memorize Channels".

DIRECT CHANNEL SELECTION buttons (0-9) - Press these buttons to select a

channel.The channel number will appear on the upper right corner of the TV screen. If an

invalid channel number is selected, the display will revert to the previous channel.

TV MODE DIRECT CHANNEL SELECTION - When the TV/CATV menu option is in the

TV position, all channels can be instantly selected by using two buttons (For example, to

select channel 2, press "0", then "2". If you press only "2", channel selection will be

delayed for a few seconds). For channels 10 and above, press the 2 digits in order.

To turn on the TV, press the POWER button.

The VOLUME can be adjusted to a desired level by pressing the VOL (VOLUME) or

DOWN button.

The sound level will be indicated on the TV screen by GREEN BARS AND A NUMBER.

As the sound level increases, so do the number of BARS AND THE NUMBER on the

screen. The same is true for decreasing the level.

Set the TV/CATV menu option to the appropriate position. When shipped from the

factory, this menu option is in the CATV setting. See "To Memorize Channels".

TV OPERATION

TV - VHF/UHF channels

CATV - CABLE TV channels

1. EAR (Earphone) Jack - Plug an earphone or monaural headphones with an 1/8 miniplug into

this jack for private listening.

2. Remote Sensor - Signals from the Remote Control unit are received here.

3. POWER Button - Press to turn the TV on or off.

4. VOLUME ▲/▼ Buttons - Press to raise or lower the level of the sound.

(MENU Buttons) - Press both VOLUME ▲/▼ Buttons al the same time to display the On-

Screen menu functions.

(SET +/ – Buttons) - Press to select the desired setting during On-Screen operations.

5. CHANNEL ▲/▼ Buttons - Press to select a higher or lower numbered channel set into memory.

(ENTER Button) - Press to enter or select information for On-Screen operations.

(RESET Button) - Press, while in the On-Screen menu mode, to reset the On-Screen picture

adjustments to their factory preset positions.

6. AUDIO VIDEO IN Jack - Audio and video signal cables from an external source can be

connected here.

CLOSED CAPTION

WHAT IS CLOSED CAPTIONING?

This television has the capability to decode and display Closed Captioned television programs.

Closed Captioning will display text on the screen for hearing impaired viewers or it will

translate and display text in another language.

TO VIEW CLOSED CAPTIONS

Press the TV/CAP/TEXT button on the remote control to switch between normal TV and the two

Closed Caption Modes (Captions and 1/2 of Full Screen Text).

Captions: This Closed Caption Mode will display text on the screen in English or another

language (depending on the setting of the Closed Captions CH. 1/2 button). Generally, Closed

Captions in English are transmitted on Captions Channel 1 and Closed Captions in other

languages are transmitted on Captions Channel 2.

Text: The Text Closed Caption Mode will usually fill 1/2 of full screen with a programming

schedule or other information. After selecting a Closed Caption Mode, it will stay in effect until

it is changed, even if the channel is changed. If the Captions signal is lost due to a commercial

or a break in the signal, the Captions will reappear when the signal is received again. If the

channels are changed, the Captions will be delayed approximately 10 seconds.

The Captions will appear in places on the screen where they will least interfere with the

picture, usually on the bottom of the screen. News programs will usually show three-line

Closed Captions which scroll onto the screen. Most other shows provide two or three lined

Captions placed near the character who is speaking so the viewer can follow the dialogue.

Words in italics or underlined describe titles, words in foreign languages or words requiring

emphasis. Words that are sung usually appear enclosed by musical notes.

For television programs broadcasting with Closed Captions, look in your TV guide for the

Closed Captions symbol (CC).

NOTES:

• If you want to change password, follow step 1 and 2 and select "CHANGE PASSWORD"

option then enter your new password.

• The V-Chip function is activated only on programs and tapes that have the rating signal.

• Once you block a program using the V-Chip function, the blocked program cannot be watched

based on the content of the show. When the program starts, the "ENTER PASSWORD" will

appear on the screen. When you want to release the V-Chip temporarily, enter the password.

If you change the channel or turn off the TV while the V-Chip function was temporarily

released, the original setting will be resumed. If you return to the channel you were watching

you must re-enter your password to temporarily release your V-Chip function again.

• When you watch the TV from the cable box or the VCR with the RF Modulator, then you

release the V-Chip temporarily, the V-Chip setting will not be resumed until you turn off the

TV. The TV channel is not used in this case.

• When changing the channel with the cable box or the VCR, approximately 10 seconds will

pass until the program appears.

• When activating the Closed Captioned Decoder, there will be a short delay before the

Closed Captioned text appears on the screen.

• Closed Captioned text is only displayed in locations where it is available.

• If no caption signal is received, no captions will appear, but the television will remain in

the Caption Mode.

• Misspellings or unusual characters may occasionally appear during Closed Captioning.

This is normal with Closed Captioning, especially with live programs. This is because

during live programs, captions are also entered live. These transmissions do not allow

time for editing.

• When Captions are being displayed, on-screen displays, such as volume and mute may

not be seen or may interfere with Closed Captions.

• Some cable systems and copy protection systems may interfere with the Closed

Captioned signal.

• If using an indoor antenna or if TV reception is very poor, the Closed Caption Decoder

may not appear or may appear with strange characters or misspelled words. In this case,

adjust the antenna for better reception or use an outdoor antenna.

CATV mode direct channel selection

When the TV/CATV menu option is in the CATV position, channels can be selected as

follows:

1-9

10-12

13-99

100-125

Press "0" twice, then 1-9 as needed.

Example, to select channel 2, press "002".

Press "0", then remaining 2 digits.

Example, to select channel 12, press "012".

Press the 2 digits in order.

Example, to select channel 36, press "36".

Press the 3 digits in order.

Example, to select channel 120, press "120".

NOTE: If the station being viewed stops broadcasting, the TV will automatically shut off

after 15 minutes.

NOTE:

If Spanish or French is chosen, the Closed Caption indicators will be in the selected language,

but the Closed Caption text will not be affected by the language selection.

Press the MENU button.

Press the SET + or – button to select the LANGUAGE

mode, then press the ENTER button.

Press the SET + or – button until the "

" indicator

points to the desired language: English (ENGLISH),

Spanish (ESPAÑOL) or French (FRANCAIS), then

press the ENTER button.

Press the MENU button again.

FRANCAIS

ENGLISH

ESPAÑOL

LANGUAGE / IDIOMA / LANGUE

〈

–

/ ENTER / MENU

〉

LANGUAGE

CH SET

PICTURE

V-CHIP SET

〈

–

/ ENTER / MENU

〉

This TV can display the channel number, on screen displays and picture adjustments on the

screen in English, Spanish or French.

On-screen language selection (step 3) will automatically appear on the screen when you press

the MENU button initially. Select the language you prefer first, then proceed with the other menu

options.

SETTING LANGUAGE

Press the MENU button.

Press the SET + or – button to select the V-CHIP SET option, then press the ENTER button.

Enter your password (4 digits) using the Direct channel selection buttons (0-9).

In the event of entering incorrect password press the RESET button. Then press the

ENTER button.

Enter the same password for confirmation, then press the ENTER button.

Press the SET + or – button to select the V-CHIP option.

Press the ENTER button to select the ON.

Press the SET + or – button to select the TV RATING or MOVIE RATING option.

Press the ENTER button.

Press the SET + or – button to select the desired rating for the applicable video or TV

channel. Press the ENTER button.

Press the MENU button until the MENU screen is cleared.

TV-Y

TV-Y7

TV-G

: all children

: 7 years old and above

: childrens program

TV-PG

TV-14

TV-MA

: parental guidance

: 14 years old and above

: 17 years old and above

When you select TV-Y7, TV-PG, TV-14 or TV-MA, press the CALL button to explain the rating.

Press the SET + or – button to select the desired rating you want. Press the ENTER button to

select the setting ON or OFF.

: all ages

: parental guidance

less than 13 years old

PG-13

NC-17

SETTING V-CHIP

This TV is fitted with a V-CHIP controller which provides you with channel viewing access

controls and restrictions. This function allows adult screening of TV programs based upon

ratings.

OFF

TV-Y7 TV-G TV-14 TV-MATV–Y TV-PG

TV RATING

MOVIE RATING

OFF

PG PG-13 R NC-17 XG

: under 17 years old parental

guidance suggested

: 17 years old and above

: adult only

SET– SET+

MT1132A MT1192A

541 23 6 5423 6

3J81201A E 31/03/2001, 19:574

1 2 3 4

Comments to this Manuals

No comments

Memorex MT1192A User Manual Page 3

Comments to this Manuals

Related products and manuals for Televisions Memorex MT1192A